Viking iMow MI manual

Specify the start and end times of the new active time in the selection window and confirm with OK. During this instruction, the user should be made aware that the utmost care and concentration are required for working with the machine. Page: DE FR NL IT EN B - EN Attach the linking section to the ground with a sufficient number of fixing pins 2. The set time must correspond to the actual time in order to prevent inadvertent mowing by the robotic mower. The machine should not be operated after the consumption of alcohol, drugs or medications which impair reactions. Only give or lend the machine to persons who are familiar with this model and how to operate it. Switching on the docking station — During automatic operation, the docking station is switched on and off automatically. These can damage plastics and metals, impairing the safe operation of your VIKING machine. Route the perimeter wire 1 from the edge to the obstacle with the correct clearance use iRuler around the obstacle 2 and attach it to the ground with a sufficient number of fixing pins 3. VIKING recommends that you have maintenance operations and repairs performed exclusively by a VIKING specialist dealer. In hot, dry conditions, the lawn should not be kept too short as it will otherwise be burnt by the sun and become unsightly. The switch and safety devices installed in the machine must not be removed or bypassed. In the event of a rollover, the wheel drive and mowing motors are switched off. The robotic mower must run completely within the mowing area and must not touch the obstacle. Flashing of the display illumination and a signal tone additionally indicate the impending start of the mowing motor. This also activates the docking station. Illustrations with text passages: Operating steps relating directly to the illustration can be found immediately after the illustration, with a corresponding reference to the item numbers. Your VIKING specialist dealer performs a variety of maintenance and service operations with the aid of this menu. Settings are confirmed and menus opened using the OK button 2. Drive to docking station: The robotic mower travels back to the docking station and charges the battery. Completion of the test run: The next step of the installation assistant is called up when the robotic mower docks following a complete circuit. VIKING recommends that the standard setting of 6 cm not be changed. One fixing pin per meter is sufficient as a rough guide.

They then fall back into the turf, where they remain and decompose. I hope that your VIKING machine will give you great enjoyment. If your health is impaired, you should consult your doctor to determine whether working with the machine is possible. Starting points: The robotic mower either starts the mowing at the docking station default setting or at a starting point. The selected submenu has a black background and is opened using the OK button. Illustrations with text passages: Operating steps relating directly to the illustration can be found immediately after the illustration, with a corresponding reference to the item numbers.

Bruksanvisning Viking iMow MI P ( sidor)

Track offset: The robotic mower travels along the perimeter wire at a 6 cm offset from the wire as standard. Active tabs and menu entries have a black background. The step "Program the robotic mower" of the installation assistant is called up. Should you require support, your VIKING specialist dealer will be pleased to assist you with preparation of the mowing area and installation of the perimeter wire. Confirm the message "Confirm each day individually or change active time" by pressing the OK button. Check the installation of the perimeter wire before it is finally secured in place. Example: The control pad 1 serves for navigation in the menus. The active button has a black background. The selected submenu has a black background and is opened using the OK button. Press the illustrated button combination to unlock. If the active times for an individual day need to be edited, the day must be activated via the control pad press to the left or right and the Active times submenu must be opened. They prevent premature wear e. The battery must be disposed of separately from the machine. Hur kort ska jag klippa gräset? These can damage plastics and metals, impairing the safe operation of your VIKING machine. Start time-delayed mowing: The robotic mower starts the mowing operation automatically, but with a time delay, following activation. Days without active times must also be confirmed with OK. Avoid contact with the mowing blade when lifting and carrying the machine. View a manual of the Viking iMow MI below. Select the required display language and confirm with the OK button.

Vad ska jag göra. Never connect the battery terminals with metallic objects short-circuit. The storage room must be dry, frost-free and lockable. The set time must correspond to the actual time in order to prevent inadvertent mowing by the robotic mower. Obstacle 1 is lower than 2 cm: Route the perimeter wire 2 without clearance to the obstacle. The distance corresponds to that covered from the docking station to the starting point in metres, measured in a clockwise direction.

Bruksanvisning Viking iMow MI ( sidor)

Selection window: Settings can be changed by pressing the control pad. Never pull out fixing pins using the perimeter wire — always use a suitable tool e. In particular, short-circuit protection must be ensured. Docking station Red LED illuminates continuously Red LED flashes slowly Red LED flashes rapidly Red LED flashes at intervals LED does not illuminate The docking station is switched on exclusively via the docked robotic mower. Genuine VIKING spare parts can be recognised by the VIKING spare parts number, by the VIKING lettering and, if present, by the VIKING spare parts symbol. Ensure correct connection of the left and right perimeter wire ends — do not interchange the wire ends. During installation, active times are automatically distributed over the entire week. Page: 97 B - EN 96 Confirm your language selection with the OK button or select "Change" and repeat the language selection. If a secondary area was installed, after pressing the OK button it is necessary to define whether mowing is taking place on a secondary area or on the main area. Correct routing of the perimeter wire and power cable must be regularly checked. The mowing blade comes to a standstill within a few seconds and the message "STOP button pressed" appears in the display. If your health is impaired, you should consult your doctor to determine whether working with the machine is possible. Events: List of the last activities of the robotic mower. Page: 92 91 DE FR NL IT EN B - EN Never allow the robotic mower to operate unattended if you know that animals or persons, particularly children, are in the vicinity. Red LED illuminates continuously: The docking station is switched on and the robotic mower is not docked. Keep packaging material away from children. Make a note of the positions of the wire connectors on the sketch of the mowing area. Then connect the mains plug. At least one starting point must be defined in these partial areas. This product has been produced using state-of-the-art production methods and extensive quality assurance procedures, because our goal is only achieved if you, the customer, are satisfied with your machine. The red STOP button on top of the machine terminates the link, the previous installation assistant step is called up. Lift the robotic mower slightly by the carrying handle 1 to relieve the weight on the drive wheels. To prevent the risk of stumbling, always drive in the fixing pins all the way. Precisely observe the free length and do not roll up protruding wire ends.

Messages: List of all active errors, faults and recommendations; shown together with the times of occurrence. This prevents the robotic mower from accidentally driving into the corridor during mowing. Any unevenness must be removed under the floor plate so that it fully contacts the ground. During installation, active times are automatically distributed over the entire week. Content of the sketch: — Contour of the mowing area including important obstacles, borders and any no-go areas which the robotic mower must not mow. It can be extended or reduced. Perform initial installation using the installation assistant.

Moreover, the applicable local regulations on the use of robotic mowers as well as the information in the "For your safety" Ö 6. Never pull out fixing pins using the perimeter wire — always use a suitable tool e. Never bend the floor plate. If errors or faults occur during the initial installation, a corresponding message appears in the display. By using the 'Select a language' button, you can choose the language of the manual you want to view. Check the clearances using the iRuler. Always use the machine in a reasonable and responsible manner and be aware that the user is responsible for accidents involving third parties or their property. Byta kniv. Allow the machine to cool for approx. Secure the machine and other machine parts being transported e. Detach electric cables at the plug and socket and not by pulling on the electric cable. Inge MattssonInga kommentarer 0. Activate the disabling device Ö 5. In particular, protect the hands when working on the mowing blade and when driving in the fixing pins or the docking station pegs. Active times which have been cancelled in this manner are greyed out in the mowing plan. Menu signal 7. Starting frequency: The starting frequency defines how often a mowing operation is to begin from a starting point. Corridor width: cm The distance to the perimeter wire within the corridor is selected randomly. Lawn status: Information on the lawn — Mowing area in square metres: This value is entered during initial installation or new installation Ö 9. Disabling device: The disabling device is activated with OK; the robotic mower can no longer be operated. Use the Back button to leave the active menu or jump one step back in the installation assistant. To check correct wire routing around no-go areas, position the robotic mower in the mowing area with the front facing the no-go area and start a test run. The press-fit connectors can only be fitted once on the perimeter wire.

Alarm signal: For switching on and off the acoustic signal that sounds when the robotic mower hits an obstacle. In corridors, the lawn is only mown along the path of the perimeter wire. High: Same as for "Medium", but an anti-theft alarm is enabled as well as the PIN code query. If the bar is moved all the way to the right, the robotic mower will only mow if the rain sensor is completely dry. The rotary knob can be removed upwards from the adjustment element. This may result in damage and expensive repairs. Disabling device: The disabling device is activated with OK; the robotic mower can no longer be operated.

Viking iMow MI 422 P bruksanvisning

Fluid may escape from the battery due to improper use — Avoid contact! The switch and safety devices installed in the machine must not be removed or bypassed. The robotic mower may travel along at a greater offset to the perimeter wire, requiring more space in corridors, confined areas and when travelling along edges. During initial installation, the robotic mower automatically calculates the mowing duration based on the specified size of the mowing area. This product has been produced using state-of-the-art production methods and extensive quality assurance procedures, because our goal is only achieved if you, the customer, are satisfied with your machine. General lists: — Use of the product for sporting or competitive events Texts with added significance: Text passages with added significance are identified using the symbols described below in order to especially emphasise them in the instruction manual: Texts relating to illustrations: Some Illustrations which are necessary for use of the machine can be found at the front of this instruction manual. Check the clearances using the iRuler. A further docking station must be linked with the robotic mower. If required, several mowing or charging operations can run during an active time. The language selected during initial installation is set as the default. An additional active time must not overlap with other active times. During this instruction, the user should be made aware that the utmost care and concentration are required for working with the machine. A mains connection is necessary for operation of the docking station. The docking station is defined as starting point 0; mowing operations are started from here as standard. Particular care is required during use in public green spaces, parks, sports fields, along roads and in agricultural and forestry businesses. Requirements: — Minimum width is 88 cm between solid obstacles in the corridor area and 22 cm between paths that can be travelled on. Automatically — by obstacles at the edge of the mowing area. Felkod Errors during normal operation are documented in the messages. The mowing operation can be initiated via the commands "Start mowing" Ö

The switch and safety devices installed in the machine must not be removed or bypassed. Avoid contact with the mowing blade when lifting and carrying the machine. Otherwise, there may be a risk of accidents resulting in personal injury or damage to the machine. Normal reception Wire signal OK: The text "Wire signal OK" appears on the display. Lift the robotic mower slightly by the carrying handle 1 to relieve the weight on the drive wheels. Only then is the robotic mower ready for operation.