Clamp Multimeter UNI-T UT :: UNI-T

When current measurement has been completed, disconnect the connection between the conductor under test and the jaw, and remove the conductor away from the transformer jaw of the Meter. Input sine wave, then adjust the reading until it is same as the effective value. Testing for Continuity see figure 6 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before measuring continuity. Press HOLD again to exit the Hold mode, the Meter beeps. The obtained reading will be more precise. Product support. H Temperature coefficient: 0. The Meter is in the auto range mode in which the Meter automatically selects the range with the best resolution. UT A Series. Related Manuals for UNI-T UT Multimeter UNI-T UT20B Operating Manual Digital multimeter 34 pages. Make sure the transformer jaw and the tets leads are disconected from the circuit being tested before opening the case bottom. Restore password. Uni-Trend Technology China Co. III V over voltage and Cancel Delete. Weight: Approximate g battery included B. III V and double insulation. UT89X Series. Uni-Trend has established collaborations with partners in over 80 countries for product distribution and services. Measuring Resistance see figure 4 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before measuring resistance. DC Voltage Range Resolution Accuracy Overload protection AC Voltage C.

Laser Rangefinders. Remark: If the reading is positive, the current direction is from bottom to up. UT-D Data Cables. DC Voltage Range Resolution Accuracy Overload protection UT-CS09 Series. For support.

Tångamperemeter UNI-T UT | Clas Ohlson

UTT Series. The th Canton Fair. Laser Distance Meters. Electrical Power Testers. When current measurement has been completed, disconnect the connection between the conductor under test and the jaw, and remove the conductor away from the transformer jaw of the Meter. Soft cloth and mild detergent should be used to clean the surface of the Meter when servicing. Socket Testers. Do not use the Meter if it is damaged or the case or part of the case is removed. Frequency Range Resolution Accuracy Overload protection 10Hz 0. Sign In OR. DC Current I. The unit of current. Center the conductor within the transformer jaws, then release the Meter slowly until the transformer jaw is completely closed. Any shock will cause the changing in reading in the short time. Digital Multimeters. Warning: To avoid false readings, which could lead to possible electric shock or personal injury, replace the battery as soon as the battery indicator appears. III V and double insulation. Upload from disk. III V over voltage and The obtained reading will be more precise.

Press to display zero. Please read the relevant information carefully and observe all the Warnings and Notes strictly. Button Operation Performed HOLD Press HOLD to enter the Hold mode in any mode, the Meter beeps. Testing for Continuity see figure 6 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before measuring continuity. UTi industrial Series. UT-L Probes and Test Leads.

UNI-T Voltage Meter, Multimeter, Oscilloscope | UNI-T

UT-S Adapter Sockets. Upload from URL. UTi industrial Series. The resistance ranges are: 10Hz, Hz, 1kHz, 10kHz, kHz, 1MHz and Black 10MHz. All Rights Reserved. UT-T Temperature Probes. Thermal Imagers. Registered Design No. Duty Cycle H. Socket Testers. Resistance D. General Meters. Connect the test leads across with the object being measured. Environmental Testers. Trade Shows. General Specifications: Maximum Voltage between any Terminals and grounding: Refer to different range input protection voltage. The unit of current. For sales contact. The measured value shows on the display. Warning Do not attempt to repair or service your Meter unless you are qualified to do so and have the relevant calibration, performance test, and service information. The obtained reading will be more precise. Industry Electricity Electronic and Electricity Environment Monitoring Ranging and Mapping Communication. New Measurement Visions.

UT-CS09 Series. Testing Diodes see figure 5 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before testing diodes. UT-T Temperature Probes. Change to AC: UT Change to AC by using average response method. Discontinued Product List. DC measuremnet mode is a default.

UNI-T UT OPERATING MANUAL Pdf Download | ManualsLib

III V and double insulation. DC Current I. Products New Products. Copyright c UNI-T. The measured value shows on the display. UT-C Alligator Clips. UT Series. UT-T Temperature Probes. Change to AC: UT Change to AC by using average response method. Socket Testers. UTT Series. Products News. Voltage and Continuity Testers. Continuity Test Range Resolution Accuracy Overload protection Around 50m Vp the buzzer beeps Remark: Open circuit voltage approximate 0. Center the conductor within the transformer jaws, then release the Meter slowly until the transformer jaw is completely closed. Refer to the Operating Manual Deficiency of Built-In Battery Continuity Test Diode Fuse Conforms to Standards of European Union All Rights Reserved. Digital Multimeters. When the pressure on the lever is released, the jaws will close. Measuring Resistance see figure 4 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before measuring resistance. DC measuremnet mode is a default. Any shock will cause the changing in reading in the short time. Input sine wave, then adjust the reading until it is same as the effective value.

DC measuremnet mode is a default. Electrical Power Testers. Power Quality Analyzers. Check the following items carefully to see any missing or damaged part: Item Description English Operating Manual 1 piece Test Lead 1 pair Test Clip 1 pair Carrying Bag 1 piece AC Voltage C. Diode measurement mode is a default or presss SELECT to select measurement mode. Environmental Requirements The Meter is suitable for indoor use.

Uni-T UT203 bruksanvisning

Press to display zero. DC Current I. DC Voltage B. The unit of current. This manual is also suitable for: Ut Continuity Test Range Resolution Accuracy Overload protection Around 50m Vp the buzzer beeps Remark: Open circuit voltage approximate 0. General Meters. All Rights Reserved. Product support. Soft cloth and mild detergent should be used to clean the surface of the Meter when servicing. Press SELECT to switch between DC and AC measurement mode. Diode Test Range Resolution Accuracy Overload protection Display forward voltage Vp drop nearest value Remark: Open circuit voltage approximate 1. III V over voltage and Laser Rangefinders. Print page 1 Print document 47 pages. Trade Shows. Center the conductor within the transformer jaws, then release the Meter slowly until the transformer jaw is completely closed. Manuals Brands UNI-T Manuals Multimeter UT Operating manual UNI-T UT Operating Manual Digital clamp multimeters. Multimeter UNI-T UT58A Operating Manual 36 pages. Press HOLD again to exit the Hold mode, the Meter beeps. When resistance measurement has been completed, disconnect the connection between the testing leads and the circuit under test and remove testing leads from the input terminals. Power Quality Analyzers.

General Meters. Industry Electricity Electronic and Electricity Environment Monitoring Ranging and Mapping Communication. AC Current Range Resolution Accuracy Frequency Response Overload protection Latest news and special events UTB Pocket Size Digital Multimeter. Uni-Trend Technology China Co. Measuring Resistance see figure 4 Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge all the high-voltage capacitors before measuring resistance. Upload from disk.