Janome Manuals, Janome Instruction Manuals - Sewing Parts Online

Insert the power supply plug r into the wall outlet t. Straight Stitch You can select the stitch patterns from 01 to 10 directly in mode 1 direct pattern selection mode. Round-End Buttonhole Shelltuck Stitch Insert the additional spool pin q into the hole w. Press and hold the button w when the machine is. For twin needle sewing, please refer to page Buy Points How it Works FAQ Contact Us Questions and Suggestions. SET THE PATTERN SELECTOR DIAL ATAND THE STITCH LENGTH CONTROL AT "S. Stippling Stitch Log in Sign up. Cancel Delete. REMOVE THE PATTERN SELECTOR DIAL. Multiple Zigzag To decrease sewing speed, slide the slider to the left. Pull the lid towards you to open the accessory storage r. Welcome to ManualMachine. Threading the Machine Raise the presser foot. Sign up! While in operation, always keep your eyes on the sewing area and do not touch any moving parts such as the thread take-up lever, handwheel or needle.

Turn on the power switch q. Viewing a Long Text Decorative Stitches Page 3 PROBLEM CAUSE REMEDY REFERENCE 3. Press and hold the button w when the machine is. Refer to page To select stitch patterns in mode 2—6, first press the mode key w to select your desired mode.

JANOME SERVICING MANUAL Pdf Download | ManualsLib

Bridge Stitches Page 4 PROBLEM CAUSE REMEDY REFERENCE 6. Stretch Buttonhole Drawn work Page Clearance Between Needle And Hook No. Remove the needle from the needle clamp w. If it still does not fit, contact a qualified electrician to install the proper outlet. Page 6: Service Access SERVICE ACCESS FACE COVER FACE COVER TO REMOVE REMOVE THE FACE COVER BY REMOVING THE CAP A AND SCREW B. Names of Parts Lower the presser bar to lock the foot into the place. Round-End Buttonhole Accessories are stored inside the extension table. Always use the proper needle plate. Keep ventilation openings of this sewing machine and foot controller free from accumulation of lint, dust and loose cloth. THREAD PATH IS USE THE PROPER THREAD INCORRECT. Do not pull or push fabric while stitching. INITIAL SEWING SPEED IS START WITH MEDIUM SPEED. Before Using Your Sewing Machine Before using your sewing machine for the first time, place a scrap of fabric under the presser foot and run the machine without thread for a few minutes. NOISY 1. Deleting and Inserting a Letter pattern Lock-a-Matic Stitch Press the mode key to change the mode. Insert the power supply plug y into the wall outlet u.

Press the flip key to flip the selected stitch pattern horizontally. Refer to pages 23 and Problems and Warning Signs Check your email for further instructions. Insert the additional spool pin q into the hole w.

Janome Symaskin bruksanvisningar

To select stitch patterns in mode 2—6, first press the mode key w to select your desired mode. The machine will trim the threads automatically after the locking stitch then stop when the reverse or autolock button is pressed, or a pattern has the auto-lock stitch programmed. Extension Table Page 44 PARTS LIST Raise the presser foot, and press the lever q on the back of the foot holder. Upload from URL. Touch Panel The machine will automatically stops. Press and hold the reverse stitch button w to sew in. Page Clearance Between Needle And Hook No. To refer to the modes and their available stitch patterns for this sewing machine, e please check the stitch chart or stitch reference on page Each time you press the mode key, the folder e indicated on the left side of the screen will change, and the mode changes as follows; Mode 1: Direct pattern selection Mode 2: Utility stitch pattern selection Mode 3: Decorative stitch pattern selection Mode 4: Number and letter selection Mode 5: European accented letter selection Mode 6: Russian Cyrillic letters selection The number on the folder e indicates the selected mode number. Do not place anything on the foot control, otherwise the machine will run inadvertently. Tighten the thumbscrew q by turning it clockwise with a screwdriver. Refer to pages 23 and The small spool holder e is used with narrow or small w spools of thread. Keep fingers away from all moving parts. THREAD 2. INITIAL SEWING SPEED IS START WITH MEDIUM SPEED. Clasp Stitch DANGER — To reduce the risk of electric shock:. We have emailed you a verification link to to complete your registration. SET THE PATTERN SELECTOR DIAL ATAND THE STITCH LENGTH CONTROL AT "S.

Press the mode key to change the mode. Blind Hemming Lift out the bobbin. Presser Foot Lifter We have emailed you a verification link to to complete your registration. You can select the stitch patterns from 01 to 10 directly in mode 1 direct pattern selection mode. Lift up the spool pin q.

Janome QDC Instruction Manual

Lower the presser. Spread the legs of large extension table. Each time you press the mode key, the folder e indicated on the left side of the screen will change, and the mode changes as follows. Forgot password? Refer to pages 23 and NEEDLE SWING Square Buttonhole The wrong foot can cause the needle to break. The machine will trim the threads automatically after the locking stitch then stop when the reverse or autolock button is pressed, or a pattern has the auto-lock stitch programmed. NEEDLE IS NOT INSERTED INSERT THE NEEDLE PROPERLY. NEEDLE IS BENT OR DULL. Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or mechanical adjustment. Darning Stitch WARNING — To reduce the risk of burns, fire, electric shock, or injury to persons:. Welcome to ManualMachine. The thread cutter mark will blink i while the machine cuts the threads. Press the twin needle button u when using a twin needle. Viewing a Long Text Raise the presser foot. Enter the 2-digit number of the desired stitch pattern with the corresponding number keys. Corded Buttonhole While in operation, always keep your eyes on the sewing area and do not touch any moving parts such as the thread take-up lever, handwheel or needle. Do not operate where aerosol spray products are being used or where oxygen is being administered.

The gap between the needle and the flat surface should be consistent. SECTION IV. Page Parts List PARTS LIST MODEL S, S Page 28 PARTS LIST To select stitch patterns in mode 2—6, first press the mode key w to select your desired mode. Insert the stitch chart q into the chart holder w. Press the auto-lock button e to sew a locking stitch at the end of current pattern. Touch Panel

Janome Instruction and Service Manuals

Welcome to ManualMachine. Names of Parts LOOSEN SETSCREWS A AND BAND THEN, REMOVE THE FRONT COVER BY REMOVING SETSCREWS C AND D. First press. If in doubt please contact your retailer for guidance. Operating Instructions Programming Letters You can continue sewing without pulling the bobbin thread up after trimming the threads. Bobbin Winding Installing the Bobbin Holder Stitch Chart Turn on the power switch q. Multiple Zigzag A fine thread and needle should be used for sewing lightweight fabrics, so the fabric will not be marred. THE CLEARANCE BETWEEN THE NEEDLE AND SHUTTLE RACE SHOULD BE —0. Page Parts List PARTS LIST MODEL S, S Page 28 PARTS LIST Enter a 2-digit pattern number to select the desired stitch pattern in mode 2 to 6. Lower the presser bar to lock the foot into the place. Insert the power supply plug r into the wall outlet t. Place a spool of thread on the. Press the flip key to flip the selected stitch pattern horizontally. Extension Table The extension table q provides an extended sewing area and can be easily removed for free arm sewing. Forgot password? Mode 5: European accented letter selection Mode 6: Russian Cyrillic letters selection. SECTION IV.

Changing the Presser Foot LOOSEN SETSCREWS A AND BAND THEN, REMOVE THE FRONT COVER BY REMOVING SETSCREWS C AND D. Machine Operating Buttons Insert the machine plug w into the power inlet e. Check your email for further instructions. Read all instructions before using this sewing machine. Bridge Stitches